fogo

used a script to remove and call cron.

the job is complex. Kodi is trying in EGAMI boxes? The answer is "yes".

if they are new. GIT change log.

https://github.com/oe-alliance/oe-alliance-tuxbox-common/tree/master/src donwload and overwrite files xml etc/tuxbox restart GUI.try now.

files xml file using tuxbox common github? or file backup? Please upload crash.log

How To Flash-image Gi-Xpeed Lx3 1.- Fully power the receiver down via the rocker switch at the rear of the receiver. 2.- Make sure no USB devices are plugged into the receiver at this point. 3.- Insert the USB stick containing the image files into one of the USB ports on the receiver. 4.- Power the receiver on from the rear rocker switch. 5.- When prompted via the receiver display-and TV, press the volume up button ^ located on the front pannel of the receiver to initiate the flashing proccess: watching on TV the following pictures: (in display) view Updating ... - when you see this picture on TV, do what he says (picture down) : 1.- REMOVE USB. 2.- PRESS POWER BUTTON (front receiver). * the receiver will be ready to reboot the flashing process has completed, and the wizard settings.

list of installed channels?

The solution then was the need to give the official dealer from whom you bought the receivers, if you've tried everything I've told you as you enter and the problem persists, treat this problem and where you should buy these receivers.

you have tried to download and install image post # 11? first should try to indicate if any image gives the same problem, has shown us that has put us tested according to two images, Egami and openatv, too poor to take tests results, you try many soft openmb, openvix, etc .. ..If the problem continues then ....according you your tuner works in another box ... then ....the problem is the motherboard of the receiver because it tells us that the tuner is fine and works on his other box. if the motherboard of the receiver and you have to contact your dealer because the problem is hardware.

download-image-factory

premium series image-factory should be work.

if it works in another box it is not tuner. then, here there is no doubt that out, install factory image http://www.miraclebox.se/downloads.html

if it is a plug and play your T2 try removing and relocating restart the box and if you can not recognize the fault is the tuner itself, and in this case should talk to your dealer and have the problem. You always try to do the test with USB flash soft clean install.try what I am indicating. if you have the opportunity try another miraclebox tuner box and leave doubts. if the problem is in the box works. HDP series recognizes While this type of tuner, the proof is that the problem is happening with any soft. I daresay the problem is hardware-tuner.

reboot your box from the menu. then output gives you that this show telnet command:

you are not remove the USB and reboot.(this is what tells the display) you turn off the rear button., remove the USB and reboot.(And this is what you do). are similar but not the same things. to see if that's what happens..

(tested with astra and hotbird). bug tuners settings: 3 ANTENNA (1 ASTRA) + (2 ANTENNA ASTRA+HOTBIRD in diseqc) =========================================================== TUNER A: single satellite astra (only a separate 1 antenna cable for astra sat) =========================================================== TUNER B: (2 ANTENNA ASTRA AND HOTBIRD) DISEQC diseqc A/B port A LNB 1 HOTBIRD port B LNB 2 ASTRA. voltage YES diseqc switch satellite only NOT =========================================================== action to detect cycle of the bug: 1º.-place channel astra recording, (tuner A working). 2º.-zap from channel to channel astra->hotbird [OK] (TUNER B workinng and work diseqc) 3º.-Return channel hotbird->astra [OK].(tuner A recording tuner B zap channel astra). 4º.-bug when playing back to back from astra-> hotbird channel. (no signal 0% in hotbird channels).[NOK] pd.- It also plays if (bug) this cycle is if you start with a recording in hotbird. someone please this dish configuration to confirm!!!!

the exact directory to manually start it in this folder: /media/mount-device/EgamiBootUpload/image.zip

okay, perfect now, I will set the new menu-setup kotkey atemio4you for skin and other things (now not perfect)... next release skin-a4you v2.2

crash.log-download crash.log have to enter the settings module keys (menu Button setup old) caused by multiquickbutton ???

campeino thanks. if mh2epgdownloader with no problems. try to correct with willy-rytec plugin->XMLTV-importer I put the thread in the evolution and construction looks.

try to solve in this thread .... http://openpli.org/forums/topic/35042-corrupted-characters-xmltv-importer-plugin-epg/

errors strange characters EPG events information. plugins->(xmltv-importer and xmltv-importer-rytec)

@a4tech.....

if you want to try, please download lx3 image, and rename the folder structure to xpeedlx3/files_image->atemio/8x00/files_image

hdmi module driver bug? ... hdmi not respond by reboot (sometimes) will not start the receiver. the bug be played when you have not chosen the receiver input in your tv. PD. confirmed by me and a friend.(not bug hdmi out 1080i) (egami 6.2). thanks.