agnagna

HI, I think is a good idea if I can swap image (little/big) in PIP function... May be in the next release? Tnx.

Hi, Automatic scan doesn't work correctly! Scan doesn't start... I waited a fw minutes but nothing.... Using isettings plugin, on Terrestrial tuner only 50 ch was found instead 290! I think it should be fix. Tnx. Note: I have Atemio Nemsis Triple tuner 2SAT+1DTT.

Hi, I solved it... Problem is if we have USUALS (motor) on a tuner. I set only 1 sat and automatic scan works correctly. Tnx.

dmesg: nand: 2048MiB, MLC, page size: 4096, OOB size: 224 brcmnand brcmnand.0: 2048MiB total, 1024KiB blocks, 4KiB pages, 27B OOB, 8-bit, BCH-24 (1KiB sector) Bad block table found at page 524032, version 0x01 Bad block table found at page 523776, version 0x01 nand_read_bbt: bad block at 0x000005a00000 nand_read_bbt: bad block at 0x000005b00000 Creating 3 MTD partitions on "brcmnand.0": 0x000000700000-0x000080000000 : "rootfs" 0x000000000000-0x000080000000 : "entire_device" 0x000000000000-0x000000700000 : "kernel" EBI CS0: setting up SPI flash spi_brcmstb spi_brcmstb.0: master is unqueued, this is deprecated spi_brcmstb spi_brcmstb.0: 1-lane output, 3-byte address m25p80 spi0.0: found en25q32b, expected m25p80 m25p80 spi0.0: en25q32b (4096 Kbytes) Creating 6 MTD partitions on "spi0.0": 0x000000000000-0x0000000a0000 : "cfe" 0x0000000a0000-0x000000280000 : "splash" 0x000000280000-0x000000300000 : "macadr" 0x000000300000-0x000000380000 : "nvram" 0x000000380000-0x0000003c0000 : "bootconfig" 0x0000003c0000-0x000000400000 : "facconfig" EBI CS3: setting up NOR flash physmap platform flash device: 00002000 at 14000000 UBI: attaching mtd0 to ubi0 usb 1-1: new high-speed USB device number 2 using ehci-brcm random: nonblocking pool is initialized usb-storage 1-1:1.0: USB Mass Storage device detected scsi2 : usb-storage 1-1:1.0 usb 8-1: new full-speed USB device number 2 using ohci-brcm usb 8-1: device descriptor read/64, error -62 usb 8-1: device descriptor read/64, error -62 usb 8-1: new full-speed USB device number 3 using ohci-brcm scsi 2:0:0:0: Direct-Access JetFlash Transcend 32GB 8.07 PQ: 0 ANSI: 4 sd 2:0:0:0: Attached scsi generic sg0 type 0 sd 2:0:0:0: [sda] 62939136 512-byte logical blocks: (32.2 GB/30.0 GiB) usb 8-1: device descriptor read/64, error -62 sd 2:0:0:0: [sda] Write Protect is off sd 2:0:0:0: [sda] Mode Sense: 23 00 00 00 sd 2:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sd 2:0:0:0: [sda] Attached SCSI removable disk usb 8-1: device descriptor read/64, error -62 usb 8-1: new full-speed USB device number 4 using ohci-brcm usb 8-1: device not accepting address 4, error -62 usb 8-1: new full-speed USB device number 5 using ohci-brcm UBI: scanning is finished UBI: attached mtd0 (name "rootfs", size 2041 MiB) to ubi0 UBI: PEB size: 1048576 bytes (1024 KiB), LEB size: 1040384 bytes UBI: min./max. I/O unit sizes: 4096/4096, sub-page size 4096 UBI: VID header offset: 4096 (aligned 4096), data offset: 8192 UBI: good PEBs: 2035, bad PEBs: 6, corrupted PEBs: 0 UBI: user volume: 1, internal volumes: 1, max. volumes count: 128 UBI: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 1425851910 UBI: available PEBs: 0, total reserved PEBs: 2035, PEBs reserved for bad PEB handling: 34 UBI: background thread "ubi_bgt0d" started, PID 65 ALSA device list: No soundcards found. UBIFS: background thread "ubifs_bgt0_0" started, PID 66 usb 8-1: device not accepting address 5, error -62 hub 8-0:1.0: unable to enumerate USB device on port 1 UBIFS: mounted UBI device 0, volume 0, name "rootfs" UBIFS: LEB size: 1040384 bytes (1016 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes UBIFS: FS size: 2053718016 bytes (1958 MiB, 1974 LEBs), journal size 12550144 bytes (11 MiB, 13 LEBs) UBIFS: reserved for root: 0 bytes (0 KiB) UBIFS: media format: w4/r0 (latest is w4/r0), UUID E9EB2888-0F0F-4290-BCB7-1D06B6502695, small LPT model VFS: Mounted root (ubifs filesystem) on device 0:11. devtmpfs: mounted Freeing unused kernel memory: 244K (80843000 - 80880000) dvb: module_layout: kernel tainted. Disabling lock debugging due to kernel taint [NEXUS_Platform_P_InitBoard] LCD device(14000000) => 94000000 [platform_i2c_mutex_init] ... fb0: brcmfb frame buffer device [MCU] ver : 2.00.41 [MCU] model : INI800AM_OLED [MCU] power : SWITCH input: dreambox front panel as /devices/virtual/input/input0 input: dreambox advanced remote control (native) as /devices/virtual/input/input1 DVB: registering new adapter (dvb) dvb dvb.0: DVB: registering adapter 0 frontend 0 (DVB-S2 NIM)... dvb dvb.0: DVB: registering adapter 0 frontend 0 (DVB-T/T2 NIM)... dvb dvb.0: DVB: registering adapter 0 frontend 0 (DVB-S2 NIM)... BKNI_P_GetTrackAllocEntry_resize: resizing from 5376->8704 BKNI_Malloc(linuxkernel) top users: blocks, bytes, filename:line 897, 53820, nexus/base/src/nexus_base_scheduler.c:450 417, 30024, magnum/commonutils/mrc/src/bmrc_monitor.c:666 [fe_get_inputband] feInfo(0x00000000) invalid EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) usbcore: registered new interface driver rtl8723au usbcore: registered new interface driver rtl8192cu [ioctlVideo_SelectSource] (0) stream_source (0 -> 1) BKNI_P_GetTrackAllocEntry_resize: resizing from 8704->14080 BKNI_Malloc(linuxkernel) top users: blocks, bytes, filename:line 1280, 272704, BSEAV/lib/utils/balloc.c:31 958, 57480, nexus/base/src/nexus_base_scheduler.c:450 615, 44280, magnum/commonutils/mrc/src/bmrc_monitor.c:666 [ioctlVideo_SelectSource] (0) stream_source (1 -> 0) [ioctlVideo_SelectSource] (0) stream_source (0 -> 1) [CIMAX] init done. [ioctlVideo_SelectSource] (0) stream_source (1 -> 0) EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ioctlVideo_SelectSource] (0) stream_source (0 -> 1) [ioctlVideo_SelectSource] (0) stream_source (1 -> 0) __clk_enable: network [1] bcm7425_pm_network_enable 00 __clk_enable: enet [1] bcm40nm_pm_genet_enable 00 bcmgenet bcmgenet.0 eth0: link up, 1000 Mbps, full duplex NET: Registered protocol family 10 [ioctlVideo_SelectSource] (0) stream_source (0 -> 1) [ioctlVideo_SelectSource] (0) stream_source (1 -> 0) [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [video_videomodepreferred_read] mode(0) not found!!! [video_policy2_write] policy(scale) not found [fp_mcu_set_wol] enable = 0 [video_videomodepreferred_read] mode(0) not found!!! [ioctlAudio_SelectSource] (0) stream_source (0 -> 0) [ioctlVideo_SelectSource] (0) stream_source (0 -> 0) [video_policy2_write] policy(scale) not found [video_policy2_write] policy(scale) not found [ioctlAudio_SelectSource] (0) stream_source (0 -> 0) [ioctlVideo_SelectSource] (0) stream_source (0 -> 0) [video_policy2_write] policy(scale) not found [ioctlAudio_SelectSource] (0) stream_source (0 -> 0) [ioctlVideo_SelectSource] (0) stream_source (0 -> 0) [video_policy2_write] policy(scale) not found [ioctlAudio_SelectSource] (0) stream_source (0 -> 0) [ioctlVideo_SelectSource] (0) stream_source (0 -> 0) [video_policy2_write] policy(scale) not found [video_policy2_write] policy(scale) not found [ioctlAudio_SelectSource] (0) stream_source (0 -> 0) [ioctlVideo_SelectSource] (0) stream_source (0 -> 0) [video_policy2_write] policy(scale) not found [video_policy2_write] policy(scale) not found [ioctlAudio_SelectSource] (0) stream_source (0 -> 0) [ioctlVideo_SelectSource] (0) stream_source (0 -> 0) [video_policy2_write] policy(scale) not found [video_policy2_write] policy(scale) not found [ioctlAudio_SelectSource] (0) stream_source (0 -> 0) [ioctlVideo_SelectSource] (0) stream_source (0 -> 0) [video_policy2_write] policy(scale) not found [video_policy2_write] policy(scale) not found [ioctlAudio_SelectSource] (0) stream_source (0 -> 0) [ioctlVideo_SelectSource] (0) stream_source (0 -> 0) [video_policy2_write] policy(scale) not found [video_policy2_write] policy(scale) not found [ioctlAudio_SelectSource] (0) stream_source (0 -> 0) [ioctlVideo_SelectSource] (0) stream_source (0 -> 0) [video_policy2_write] policy(scale) not found [ioctlAudio_SelectSource] (0) stream_source (0 -> 0) [ioctlVideo_SelectSource] (0) stream_source (0 -> 0) [video_policy2_write] policy(scale) not found [video_policy2_write] policy(scale) not found [ioctlAudio_SelectSource] (0) stream_source (0 -> 0) [ioctlVideo_SelectSource] (0) stream_source (0 -> 0) [video_policy2_write] policy(scale) not found [video_policy2_write] policy(scale) not found [ioctlAudio_SelectSource] (0) stream_source (0 -> 0) [ioctlVideo_SelectSource] (0) stream_source (0 -> 0) [video_policy2_write] policy(scale) not found [video_videomodepreferred_read] mode(0) not found!!! ------------[ cut here ]------------ WARNING: CPU: 0 PID: 84 at lib/vsprintf.c:1651 vsnprintf+0x484/0x4b8() Modules linked in: ipv6 8192cu(O) 8723au(O) dvb(OF) CPU: 0 PID: 84 Comm: nx_sched_low_st Tainted: GF O 3.14.2 #1 Stack : 00000000 00000001 00000000 00000000 00000000 00000000 80886ad2 00000045 00000000 00000054 00000000 807f0000 807f66e7 cfe4e7d0 8074abd4 00000054 00000000 808838d8 e1a10000 e128d7a8 00000000 80696c44 10008703 8002dabc 00000000 00000000 80750218 cf7cfb44 cf7cfb44 807f0000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 cf7cfac0 ... Call Trace: [<8000c89c>] show_stack+0x64/0x7c [<806977f8>] dump_stack+0xc8/0xfc [<8002dc74>] warn_slowpath_common+0x84/0xb4 [<8002dd2c>] warn_slowpath_null+0x18/0x24 [<80356548>] vsnprintf+0x484/0x4b8 [<e1359d7c>] BKNI_Snprintf+0x28/0x34 [dvb] [<e128d8c0>] msgReceived_callback+0x118/0x330 [dvb] [<e12a606c>] NEXUS_P_Scheduler_Step+0x260/0x8f8 [dvb] [<e12a6738>] NEXUS_P_Scheduler_Thread+0x34/0x50 [dvb] [<e12a776c>] NEXUS_P_ThreadStart+0x7c/0xc8 [dvb] [<80050514>] kthread+0x10c/0x124 [<80006c28>] ret_from_kernel_thread+0x14/0x1c ---[ end trace 55d05da9c509a884 ]--- [ioctlVideo_SelectSource] (0) stream_source (0 -> 1) [ioctlVideo_SelectSource] (0) stream_source (1 -> 0) [video_videomodepreferred_read] mode(0) not found!!! [video_policy2_write] policy(scale) not found [fp_mcu_set_wol] enable = 0 [video_videomodepreferred_read] mode(0) not found!!! [ioctlAudio_SelectSource] (0) stream_source (0 -> 0) [ioctlVideo_SelectSource] (0) stream_source (0 -> 0) [video_policy2_write] policy(scale) not found [ioctlAudio_SelectSource] (0) stream_source (0 -> 0) [ioctlVideo_SelectSource] (0) stream_source (0 -> 0) [video_policy2_write] policy(scale) not found [video_policy2_write] policy(scale) not found [ioctlAudio_SelectSource] (0) stream_source (0 -> 0) [ioctlVideo_SelectSource] (0) stream_source (0 -> 0) [video_policy2_write] policy(scale) not found [video_videomodepreferred_read] mode(0) not found!!! DTT Tuner is original Atemio (tuner - Italy region.

May be problem is only for Atemio...

Installation starts.... but errors occours during installation..and it faulty! Please, check. I tryed to install cpying file.zip on /media/hdd/egamibootupload/ but installation doesn't work correctly! Tnx. PS:for some image it use Xpeed Lx3 or Xtrend10000 file?

Hi, I'm using last Egami 6.6.3 but I can not manage Wlan? Where Can I find wlan option in Menu? Tnx.

Hi, I reinstalled Egami Image but Wlan is missed! I tryed to load Titan+E2 original firmware... - E2 have no Wlan option. - Titan has Wlan option but No wifi-network is found! May be driver wifi problem? May be Wifi chip faulty? Please, help me... Tnx.

dmesg: usbcore: registered new interface driver usbhid usbhid: USB HID core driver TCP: cubic registered NET: Registered protocol family 17 Bluetooth: HIDP (Human Interface Emulation) ver 1.2 Bluetooth: HIDP socket layer initialized Key type dns_resolver registered PM: CP0 COUNT/COMPARE frequency does not depend on divisor EBI CS1: setting up NAND flash (primary) nand: Failed to detect ONFI extended param page nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x48 nand: Micron MT29F16G08CBACAWP nand: 2048MiB, MLC, page size: 4096, OOB size: 224 nand: Failed to detect ONFI extended param page nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x48 nand: Micron MT29F16G08CBACAWP nand: 2048MiB, MLC, page size: 4096, OOB size: 224 brcmnand brcmnand.0: 2048MiB total, 1024KiB blocks, 4KiB pages, 27B OOB, 8-bit, BCH-24 (1KiB sector) Bad block table found at page 524032, version 0x01 Bad block table found at page 523776, version 0x01 nand_read_bbt: bad block at 0x000005a00000 nand_read_bbt: bad block at 0x000005b00000 Creating 3 MTD partitions on "brcmnand.0": 0x000000700000-0x000080000000 : "rootfs" 0x000000000000-0x000080000000 : "entire_device" 0x000000000000-0x000000700000 : "kernel" EBI CS0: setting up SPI flash spi_brcmstb spi_brcmstb.0: master is unqueued, this is deprecated spi_brcmstb spi_brcmstb.0: 1-lane output, 3-byte address m25p80 spi0.0: found en25q32b, expected m25p80 m25p80 spi0.0: en25q32b (4096 Kbytes) Creating 6 MTD partitions on "spi0.0": 0x000000000000-0x0000000a0000 : "cfe" 0x0000000a0000-0x000000280000 : "splash" 0x000000280000-0x000000300000 : "macadr" 0x000000300000-0x000000380000 : "nvram" 0x000000380000-0x0000003c0000 : "bootconfig" 0x0000003c0000-0x000000400000 : "facconfig" EBI CS3: setting up NOR flash physmap platform flash device: 00002000 at 14000000 UBI: attaching mtd0 to ubi0 usb 8-1: new full-speed USB device number 2 using ohci-brcm random: nonblocking pool is initialized usb 8-1: device descriptor read/64, error -62 usb 8-1: device descriptor read/64, error -62 usb 8-1: new full-speed USB device number 3 using ohci-brcm usb 8-1: device descriptor read/64, error -62 usb 8-1: device descriptor read/64, error -62 usb 8-1: new full-speed USB device number 4 using ohci-brcm usb 8-1: device not accepting address 4, error -62 usb 8-1: new full-speed USB device number 5 using ohci-brcm UBI: scanning is finished UBI: attached mtd0 (name "rootfs", size 2041 MiB) to ubi0 UBI: PEB size: 1048576 bytes (1024 KiB), LEB size: 1040384 bytes UBI: min./max. I/O unit sizes: 4096/4096, sub-page size 4096 UBI: VID header offset: 4096 (aligned 4096), data offset: 8192 UBI: good PEBs: 2035, bad PEBs: 6, corrupted PEBs: 0 UBI: user volume: 1, internal volumes: 1, max. volumes count: 128 UBI: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 1425851910 UBI: available PEBs: 0, total reserved PEBs: 2035, PEBs reserved for bad PEB handling: 34 ALSA device list: UBI: background thread "ubi_bgt0d" started, PID 62 usb 8-1: device not accepting address 5, error -62 hub 8-0:1.0: unable to enumerate USB device on port 1 No soundcards found. UBIFS: background thread "ubifs_bgt0_0" started, PID 63 usb 1-1: new high-speed USB device number 2 using ehci-brcm usb-storage 1-1:1.0: USB Mass Storage device detected scsi2 : usb-storage 1-1:1.0 UBIFS: mounted UBI device 0, volume 0, name "rootfs" UBIFS: LEB size: 1040384 bytes (1016 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes UBIFS: FS size: 2053718016 bytes (1958 MiB, 1974 LEBs), journal size 12550144 bytes (11 MiB, 13 LEBs) UBIFS: reserved for root: 0 bytes (0 KiB) UBIFS: media format: w4/r0 (latest is w4/r0), UUID E9EB2888-0F0F-4290-BCB7-1D06B6502695, small LPT model VFS: Mounted root (ubifs filesystem) on device 0:11. devtmpfs: mounted Freeing unused kernel memory: 244K (80843000 - 80880000) scsi 2:0:0:0: Direct-Access JetFlash Transcend 32GB 8.07 PQ: 0 ANSI: 4 sd 2:0:0:0: Attached scsi generic sg0 type 0 sd 2:0:0:0: [sda] 62939136 512-byte logical blocks: (32.2 GB/30.0 GiB) sd 2:0:0:0: [sda] Write Protect is off sd 2:0:0:0: [sda] Mode Sense: 23 00 00 00 sd 2:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sd 2:0:0:0: [sda] Attached SCSI removable disk dvb: module_layout: kernel tainted. Disabling lock debugging due to kernel taint [NEXUS_Platform_P_InitBoard] LCD device(14000000) => 94000000 [platform_i2c_mutex_init] ... fb0: brcmfb frame buffer device [MCU] ver : 2.00.41 [MCU] model : INI800AM_OLED [MCU] power : RCU input: dreambox front panel as /devices/virtual/input/input0 input: dreambox advanced remote control (native) as /devices/virtual/input/input1 DVB: registering new adapter (dvb) dvb dvb.0: DVB: registering adapter 0 frontend 0 (DVB-S2 NIM)... dvb dvb.0: DVB: registering adapter 0 frontend 0 (DVB-T/T2 NIM)... dvb dvb.0: DVB: registering adapter 0 frontend 0 (DVB-S2 NIM)... BKNI_P_GetTrackAllocEntry_resize: resizing from 5376->8704 BKNI_Malloc(linuxkernel) top users: blocks, bytes, filename:line 897, 53820, nexus/base/src/nexus_base_scheduler.c:450 416, 29952, magnum/commonutils/mrc/src/bmrc_monitor.c:666 [fe_get_inputband] feInfo(0x00000000) invalid EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) usbcore: registered new interface driver rtl8723au usbcore: registered new interface driver rtl8192cu [ioctlVideo_SelectSource] (0) stream_source (0 -> 1) BKNI_P_GetTrackAllocEntry_resize: resizing from 8704->14080 BKNI_Malloc(linuxkernel) top users: blocks, bytes, filename:line 1280, 272704, BSEAV/lib/utils/balloc.c:31 958, 57480, nexus/base/src/nexus_base_scheduler.c:450 615, 44280, magnum/commonutils/mrc/src/bmrc_monitor.c:666 [ioctlVideo_SelectSource] (0) stream_source (1 -> 0) [CIMAX] init done. [ioctlVideo_SelectSource] (0) stream_source (0 -> 1) [ioctlVideo_SelectSource] (0) stream_source (1 -> 0) EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ioctlVideo_SelectSource] (0) stream_source (0 -> 1) [ioctlVideo_SelectSource] (0) stream_source (1 -> 0) __clk_enable: network [1] bcm7425_pm_network_enable 00 __clk_enable: enet [1] bcm40nm_pm_genet_enable 00 bcmgenet bcmgenet.0 eth0: link up, 1000 Mbps, full duplex NET: Registered protocol family 10 [ioctlVideo_SelectSource] (0) stream_source (0 -> 1) [ioctlVideo_SelectSource] (0) stream_source (1 -> 0) [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [fe_get_inputband] feInfo(0x00000000) invalid [video_videomodepreferred_read] mode(0) not found!!! [video_policy2_write] policy(scale) not found [fp_mcu_set_wol] enable = 0 [video_videomodepreferred_read] mode(0) not found!!! [ioctlAudio_SelectSource] (0) stream_source (0 -> 0) [ioctlVideo_SelectSource] (0) stream_source (0 -> 0) [video_policy2_write] policy(scale) not found [video_policy2_write] policy(scale) not found [ioctlAudio_SelectSource] (0) stream_source (0 -> 0) [ioctlVideo_SelectSource] (0) stream_source (0 -> 0) [video_policy2_write] policy(scale) not found dvb_demux_feed_del: feed not in list (type=0 state=0 pid=ffff) [ioctlAudio_SelectSource] (0) stream_source (0 -> 0) [ioctlVideo_SelectSource] (0) stream_source (0 -> 0) [video_policy2_write] policy(scale) not found [ioctlAudio_SelectSource] (0) stream_source (0 -> 0) [ioctlVideo_SelectSource] (0) stream_source (0 -> 0) [video_policy2_write] policy(scale) not found [ioctlAudio_SelectSource] (0) stream_source (0 -> 0) [ioctlVideo_SelectSource] (0) stream_source (0 -> 0) [video_policy2_write] policy(scale) not found [ioctlAudio_SelectSource] (0) stream_source (0 -> 0) [ioctlVideo_SelectSource] (0) stream_source (0 -> 0) [video_policy2_write] policy(scale) not found [ioctlAudio_SelectSource] (0) stream_source (0 -> 0) [ioctlVideo_SelectSource] (0) stream_source (0 -> 0) [video_policy2_write] policy(scale) not found [video_policy2_write] policy(scale) not found [video_policy2_write] policy(scale) not found dvb_demux_feed_del: feed not in list (type=0 state=0 pid=ffff) dvb_demux_feed_del: feed not in list (type=0 state=0 pid=ffff) [ioctlAudio_SelectSource] (0) stream_source (0 -> 0) [ioctlVideo_SelectSource] (0) stream_source (0 -> 0) [video_policy2_write] policy(scale) not found [ioctlAudio_SelectSource] (0) stream_source (0 -> 0) [ioctlVideo_SelectSource] (0) stream_source (0 -> 0) [video_policy2_write] policy(scale) not found [ioctlAudio_SelectSource] (0) stream_source (0 -> 0) [ioctlVideo_SelectSource] (0) stream_source (0 -> 0) [video_policy2_write] policy(scale) not found [ioctlAudio_SelectSource] (0) stream_source (0 -> 0) [ioctlVideo_SelectSource] (0) stream_source (0 -> 0) [video_policy2_write] policy(scale) not found [video_videomodepreferred_read] mode(0) not found!!! ------------[ cut here ]------------ WARNING: CPU: 0 PID: 84 at lib/vsprintf.c:1651 vsnprintf+0x484/0x4b8() Modules linked in: ipv6 8192cu(O) 8723au(O) dvb(OF) CPU: 0 PID: 84 Comm: nx_sched_low_st Tainted: GF O 3.14.2 #1 Stack : 00000000 00000001 00000000 00000000 00000000 00000000 80886ad2 00000045 00000000 00000054 00000000 807f0000 807f66e7 cfe7ad08 8074abd4 00000054 00000000 808838d8 e1a10000 e128d7a8 00000000 80696c44 10008703 8002dabc 00000000 00000000 80750218 cf071b44 cf071b44 807f0000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 cf071ac0 ... Call Trace: [<8000c89c>] show_stack+0x64/0x7c [<806977f8>] dump_stack+0xc8/0xfc [<8002dc74>] warn_slowpath_common+0x84/0xb4 [<8002dd2c>] warn_slowpath_null+0x18/0x24 [<80356548>] vsnprintf+0x484/0x4b8 [<e1359d7c>] BKNI_Snprintf+0x28/0x34 [dvb] [<e128d8c0>] msgReceived_callback+0x118/0x330 [dvb] [<e12a606c>] NEXUS_P_Scheduler_Step+0x260/0x8f8 [dvb] [<e12a6738>] NEXUS_P_Scheduler_Thread+0x34/0x50 [dvb] [<e12a776c>] NEXUS_P_ThreadStart+0x7c/0xc8 [dvb] [<80050514>] kthread+0x10c/0x124 [<80006c28>] ret_from_kernel_thread+0x14/0x1c ---[ end trace ba5bbb8e076ef43d ]--- [ioctlAudio_SelectSource] (0) stream_source (0 -> 0) [ioctlVideo_SelectSource] (0) stream_source (0 -> 0) [video_policy2_write] policy(scale) not found [ioctlAudio_SelectSource] (0) stream_source (0 -> 0) [ioctlVideo_SelectSource] (0) stream_source (0 -> 0) [video_policy2_write] policy(scale) not found [video_policy2_write] policy(scale) not found

HI, I have only Lan option in: Menu - Settings - System - Network - Device setup ! Must I reload egami 6.6.3 image? Tnx.